podpora radice Intel [bylo Re: 6.3-prelease buildworld]

[Jiri Mikulas]

Ahoj
FYI
vcera jsem instaloval 7-BETA4 na Intel  desku (DP35DP) s P35 chipsetem, 
v dokumentaci uvadeji **Storage Technology **ICH9R
SATA je v biosu nastaveno v rezimu AHCI, disky Seagate v rezimu SATA300 
(bylo potreba vytahnout na discich jumpery)

atapci1: <Intel AHCI controller> port 
0x4428-0x442f,0x4434-0x4437,0x4420-0x4427,0x4430-0x4433,0x4020-0x403f 
mem 0x90325000-0x903257ff irq 21 at device 31.2 on pci0
atapci1: [ITHREAD]
atapci1: AHCI Version 01.20 controller with 6 ports detected
ata3: <ATA channel 0> on atapci1
ata3: [ITHREAD]
ata4: <ATA channel 1> on atapci1
ata4: [ITHREAD]
ata5: <ATA channel 2> on atapci1
ata5: [ITHREAD]
ata6: <ATA channel 3> on atapci1
ata6: [ITHREAD]
ata7: <ATA channel 4> on atapci1
ata7: [ITHREAD]
ata8: <ATA channel 5> on atapci1
ata8: [ITHREAD]
~~~~~~~~~~~~~~~~~~~~~~~~~
ad6: 238475MB <Seagate ST3250310AS 3.AAC> at ata3-master SATA300
ad8: 238475MB <Seagate ST3250310AS 3.AAC> at ata4-master SATA300
~~~~~~~~~~~~~~~~~~~~~~~~~
atapci1 at pci0:0:31:2:    class=0x010601 card=0x50448086 chip=0x29228086 
rev=0x02 hdr=0x00
    vendor     = 'Intel Corporation'
    device     = '82801IB/IR/IH (ICH9 Family) 6 port SATA AHCI Controller'
    class      = mass storage
~~~~~~~~~~~~~~~~~~~~~~~~~

guli
 
Miroslav Lachman napsal(a):
> Dan Lukes wrote:
>   
>> Miroslav Lachman napsal/wrote, On 12/27/07 22:11:
>>
>>     
>>> No ja zrovna pred par dny instaloval FreeBSD 7 na nejaky Intel 
>>> (desktopovy board) a to melo snad ICH9 a system na nem nenasel disky v 
>>> rezimu AHCI, pouze v rezimu IDE kompatibility.
>>>       
>> 	To me trochu prekvapuje, protoze moje "masina na hrani" ma sobe 
>> 6.3-PRERELEASE a disky nasla - pokud se to da soudit z toho, ze z ni 
>> zrovna pisu:
>>
>>   -----------------------------------
>> atapci1 at pci0:31:2:
>>   class=0x010601 card=0x73451462 chip=0x29228086 rev=0x02 hdr=0x00
>>   vendor     = 'Intel Corporation'
>>   device     = '82801IB/IR/IH (ICH9 Family) 6 port SATA AHCI Controller'
>>   class      = mass storage
>>   port 0xa000-0xa007,0x9c00-0x9c03,0x9880-0x9887,
>>        0x9800-0x9803,0x9480-0x949f
>>   mem 0xf9fff000-0xf9fff7ff
>>   irq 19 at device 31.2 on pci0
>>   AHCI Version 01.20 controller with 6 ports detected
>> ata4: <ATA channel 0> on atapci1
>> ata5: <ATA channel 1> on atapci1
>> ata6: <ATA channel 2> on atapci1
>> ata7: <ATA channel 3> on atapci1
>> ata8: <ATA channel 4> on atapci1
>> ata9: <ATA channel 5> on atapci1
>>
>> ad12: 239372MB <WDC WD2500YS-01SHB0 20.06C03> at ata6-master SATA300
>> Trying to mount root from ufs:/dev/ad12s2a
>>   -----------------------------------
>>
>> 	Ale ICH9 existuji v nekolika modifikacich - takze by vysvetlenim mohlo 
>> byt to, ze mas nejaky jiny, nepodporovany. Varianta, ze by tu byl nejaky 
>> radic podporovany v 6.3 ale nepodporovany v 7.0 mi nepripada pravdepodobna.
>>     
>
> atapci1 at pci0:0:31:2:    class=0x01018f card=0x82771043 chip=0x29208086 
> rev=0x02 hdr=0x00
>      vendor     = 'Intel Corporation'
>      device     = '82801IB/IR/IH (ICH9 Family) 4 port Serial ATA Storage 
> Controller 1'
>      class      = mass storage
>      subclass   = ATA
>
> atapci1: <Intel ICH9 SATA300 controller> port 
> 0xb000-0xb007,0xac00-0xac03,0xa880-0xa887,0xa800-0xa803,0xa480-0xa48f,0xa400-0xa40f 
> irq 22 at device 31.2 on pci
> 0
> atapci1: [ITHREAD]
> ata5: <ATA channel 0> on atapci1
> ata5: [ITHREAD]
> ata6: <ATA channel 1> on atapci1
> ata6: [ITHREAD]
>
> ad10: 238475MB <WDC WD2500AVJS-63WDA0 12.01B02> at ata5-master SATA150
> ad12: 238475MB <WDC WD2500AVJS-63WDA0 12.01B02> at ata6-master SATA150
>
> Ted kdyz to znovu vidim takhle pred sebou, tak uz asi i tusim, kde je 
> problem - firma, co ten "server" sestavila, nechala disky najumperovane 
> na SATA150, nebo to jsou primo SATA I disky a tam je mozne, ze to s AHCI 
> nefunguje (ale nejsem si tim jisty, kdekoliv jinde mam AHCI a SATA II 
> [SATA300] disky)
>
> # uname -srmi
> FreeBSD 7.0-BETA4 i386 GENERIC
>
> Mirek
>