[Fwd: SMP s dual XEON]

kenny at schizofrenia.org kenny at schizofrenia.org
Mon Jan 16 18:48:44 CET 2006


Zdravim vsechny,

Resim problem se smp na dual cpu xeon na freebsd 6.0, bios dual cpu
inicializuje, mptable druhy cpu vidi ale kernel ho neinicializuje, skousel
sem to s generic kernelem se smp podporou. Novejsi bios pro desku neni.
Neresili jste nekdo podobny problem?

Diky za rady

Martin

HW:
deska - MSI E7320 master2
cpu - 2x Intel Xeon 3.2GHz 800FSB 64bit
mem - DDR2 400MHz ECC registered

mptable a dmesg:

bash-2.05b# mptable -dmesg

===============================================================================

MPTable

-------------------------------------------------------------------------------

MP Floating Pointer Structure:

  location:                     BIOS
  physical address:             0x000f6b20
  signature:                    '_MP_'
  length:                       16 bytes
  version:                      1.4
  checksum:                     0x3f
  mode:                         Virtual Wire

-------------------------------------------------------------------------------

MP Config Table Header:

  physical address:             0x0009b8a0
  signature:                    'PCMP'
  base table length:            324
  version:                      1.4
  checksum:                     0x69
  OEM ID:                       'INTEL   '
  Product ID:                   'Tumwater    '
  OEM table pointer:            0x00000000
  OEM table size:               0
  entry count:                  32
  local APIC address:           0xfee00000
  extended table length:        140
  extended table checksum:      19

-------------------------------------------------------------------------------

MP Config Base Table Entries:

--
Processors:     APIC ID Version State           Family  Model   Step    Flags
                 0       0x14    BSP, usable     15      4       3
0xbfebfbff
                 6       0x14    AP, usable      15      4       3
0xbfebfbff
--
Bus:            Bus ID  Type
                 0       PCI
                 1       PCI
                 2       PCI
                 3       PCI
                 4       PCI
                 5       PCI
                 6       ISA
--
I/O APICs:      APIC ID Version State           Address
                 2       0x20    usable          0xfec00000
                 3       0x20    usable          0xfec10000
--
I/O Ints:       Type    Polarity    Trigger     Bus ID   IRQ    APIC ID PIN#
                ExtINT  active-hi        edge        6     0          2   
0 INT     active-hi        edge        6     1          2 
  1 INT     active-hi        edge        6     0         
2    2 INT     active-hi        edge        6     3       
  2    3 INT     active-hi        edge        6     4     
    2    4 INT     active-lo       level        0  29:A   
      2   16 INT     active-hi        edge        6     6 
        2    6 INT     active-hi        edge        6    
7          2    7 INT     active-hi        edge        6  
  8          2    8 INT     active-hi        edge        6
    9          2    9 INT     active-lo       level       
0  29:D          2   23 INT     active-lo       level     
  0  29:B          2   19 INT     active-hi        edge   
    6    12          2   12 INT     active-hi        edge 
      6    13          2   13 INT     active-hi       
edge        6    14          2   14 INT     active-hi     
  edge        6    15          2   15 INT     active-lo   
   level        2   0:A          2   16 INT     active-lo 
     level        4   4:A          2   16 INT    
active-lo       level        4   6:A          2   19
--
Local Ints:     Type    Polarity    Trigger     Bus ID   IRQ    APIC ID PIN#
                ExtINT  active-hi        edge        6     0        255   
0 NMI     active-hi        edge        6     0        255 
  1

-------------------------------------------------------------------------------

MP Config Extended Table Entries:

--
System Address Space
 bus ID: 0 address type: I/O address
 address base: 0x0
 address range: 0x10000
--
System Address Space
 bus ID: 0 address type: memory address
 address base: 0x28000000
 address range: 0xd6e00000
--
System Address Space
 bus ID: 0 address type: memory address
 address base: 0xfee01000
 address range: 0x11ff000
--
System Address Space
 bus ID: 4 address type: memory address
 address base: 0xa0000
 address range: 0x20000
--
System Address Space
 bus ID: 4 address type: memory address
 address base: 0xd0000
 address range: 0x14000
--
Bus Heirarchy
 bus ID: 6 bus info: 0x01 parent bus ID: 0
--
Compatibility Bus Address
 bus ID: 0 address modifier: add
 predefined range: 0x00000000
--
Compatibility Bus Address
 bus ID: 0 address modifier: add
 predefined range: 0x00000001
--
Compatibility Bus Address
 bus ID: 5 address modifier: subtract
 predefined range: 0x00000000
--
Compatibility Bus Address
 bus ID: 5 address modifier: subtract
 predefined range: 0x00000001

-------------------------------------------------------------------------------

dmesg output:

Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 6.0-RELEASE-p2 #0: Sun Jan 15 23:22:02 CET 2006
    kenny at pochybny.net:/usr/obj/usr/src/sys/SMP
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Xeon(TM) CPU 3.20GHz (3200.13-MHz K8-class CPU)
  Origin = "GenuineIntel"  Id = 0xf43  Stepping = 3
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
Features2=0x641d<SSE3,RSVD2,MON,DS_CPL,CNTX-ID,CX16,<b14>>
  AMD Features=0x20100800<SYSCALL,NX,LM>
  Hyperthreading: 2 logical CPUs
real memory  = 4966055936 (4736 MB)
avail memory = 4127387648 (3936 MB)
cpu0 on motherboard
pcib0: <Host to PCI bridge> pcibus 0 on motherboard
pci0: <PCI bus> on pcib0
pci0: <unknown> at device 0.1 (no driver attached)
pcib1: <PCI-PCI bridge> irq 5 at device 2.0 on pci0
pci1: <PCI bus> on pcib1
pcib2: <PCI-PCI bridge> at device 3.0 on pci0
pci2: <PCI bus> on pcib2
bge0: <Broadcom BCM5721 Gigabit Ethernet, ASIC rev. 0x4001> mem
0xdd100000-0xdd10ffff irq 5 at device 0.0 on pci2
miibus0: <MII bus> on bge0
brgphy0: <BCM5750 10/100/1000baseTX PHY> on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX-FDX, auto
bge0: Ethernet address: 00:13:d3:be:b2:c1
pcib3: <PCI-PCI bridge> at device 28.0 on pci0
pci3: <PCI bus> on pcib3
uhci0: <UHCI (generic) USB controller> port 0x1400-0x141f irq 5 at device
29.0 on pci0
uhci0: [GIANT-LOCKED]
usb0: <UHCI (generic) USB controller> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <UHCI (generic) USB controller> port 0x1420-0x143f irq 11 at device
29.1 on pci0
uhci1: [GIANT-LOCKED]
usb1: <UHCI (generic) USB controller> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
pci0: <base peripheral> at device 29.4 (no driver attached)
pci0: <base peripheral, interrupt controller> at device 29.5 (no driver
attached)
ehci0: <EHCI (generic) USB 2.0 controller> mem 0xdd000400-0xdd0007ff irq
10 at device 29.7 on pci0
ehci0: [GIANT-LOCKED]
usb2: EHCI version 1.0
usb2: companion controllers, 2 ports each: usb0 usb1
usb2: <EHCI (generic) USB 2.0 controller> on ehci0
usb2: USB revision 2.0
uhub2: Intel EHCI root hub, class 9/0, rev 2.00/1.00, addr 1
uhub2: 4 ports with 4 removable, self powered
pcib4: <PCI-PCI bridge> at device 30.0 on pci0
pci4: <PCI bus> on pcib4
atapci0: <SiI 3114 SATA150 controller> port
0x2420-0x2427,0x2414-0x2417,0x2418-0x241f,0x2410-0x2413,0x2400-0x240f mem
0xdd200000-0xdd2003ff irq 5 at device 4.0 on pci4
ata2: <ATA channel 0> on atapci0
ata3: <ATA channel 1> on atapci0
ata4: <ATA channel 2> on atapci0
ata5: <ATA channel 3> on atapci0
pci4: <display, VGA> at device 5.0 (no driver attached)
bge1: <Broadcom BCM5705 Gigabit Ethernet, ASIC rev. 0x3003> mem
0xdd210000-0xdd21ffff irq 11 at device 6.0 on pci4
miibus1: <MII bus> on bge1
brgphy1: <BCM5705 10/100/1000baseTX PHY> on miibus1
brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX,
1000baseTX-FDX, auto
bge1: Ethernet address: 00:13:d3:be:b2:c0
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci1: <Intel 6300ESB UDMA100 controller> port
0x1f0-0x1f7,0x3f6,0x170-0x177,0x376,0x1460-0x146f at device 31.1 on pci0
ata0: <ATA channel 0> on atapci1
ata1: <ATA channel 1> on atapci1
pci0: <serial bus, SMBus> at device 31.3 (no driver attached)
orm0: <ISA Option ROMs> at iomem
0xc0000-0xc7fff,0xc8000-0xc97ff,0xc9800-0xcafff,0xcb000-0xcf7ff on isa0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
fdc0: <Enhanced floppy controller> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2
on isa0
fdc0: [FAST]
ppc0: cannot reserve I/O port range
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1 at port 0x2f8-0x2ff irq 3 on isa0
sio1: type 16550A
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 3200132000 Hz quality 800
Timecounters tick every 1.000 msec
ad0: 76319MB <WDC WD800JB-00JJC0 05.01C05> at ata0-master UDMA100
ad2: 76319MB <WDC WD800JB-00JJA0 05.01C05> at ata1-master UDMA100
ad4: 238475MB <WDC WD2500KS-00MJB0 02.01C03> at ata2-master SATA150 ad6:
238475MB <WDC WD2500KS-00MJB0 02.01C03> at ata3-master SATA150 ad8:
238475MB <WDC WD2500KS-00MJB0 02.01C03> at ata4-master SATA150 ad10:
238475MB <WDC WD2500KS-00MJB0 02.01C03> at ata5-master SATA150 Trying to
mount root from ufs:/dev/ad0s1a

===============================================================================

bash-2.05b#







More information about the Users-l mailing list