RIS na FreeBSD

HUHUALABAMA huhualabama at tiscali.cz
Tue Aug 23 20:57:40 CEST 2005
Previous message: kryptovany filesystem
Next message: OT: Solaris
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
Dobrý den,

mam mozna blby dotaz, ale zajimalo by mne jestli je mozne na FreeBSD
zprovoznit RIS server, tedy stacilo by mne jenom server pro diskless
klienty s Windows. (nejsem si jist zdali to neni to same)

Potreboval bych nabootovat s PXE ze site OS Windows PE.
Zkousel jsem googlem hledat neco podobneho, ale nasel jsem jenom
manualy jak udelat server pro diskless BSD klienty. Proto bych se vas
chtel zeptat jestli s tim nahodou nemate nejake zkusenosti a jestli to
nahodou neni podobne (stejne) jako pro bsd klienty.

Staci mi rada kde hledat blizsi informace.



Jeste bych mel jeden dotaz a ten se tyka varovnych hlasek pri
rozdelovani disku v prubehu instalace. Na netu jsem nasel jeden podobny
problem chybne detekce geometrie disku s radicem LSI 150-6,
ale odpoved na nej znela " mam ho taky a mne to jede bez problemu,
toho si nevsimej....."


Opravdu si toho nemusim vsimat ????

Predem moc dekuji

       s pozdravem Karel






Blizsi info:
*************************************
Server Acer Altos G710
Chipset E7520
2x CPU Intel(R) Xeon(TM) CPU 3.00GHz (3000.12-MHz 686-class CPU)
2x LSI MegaRAID SATA 150-6D FW 713N
4x HDD WD WD2000JD-00HBB0 08.02D08   RAID-5
6x HDD WD WD2500JD-00HBB0 08.02D08   RAID-5

http://global.acer.com/products/server/altosg710.htm#01


---------------------------------------------------------------------
WARNING:  A geometry of 72961/255/63 for amrd0 is incorrect.  Using 
a more likely geometry.  If this geometry is incorrect or you      
are unsure as to whether or not it's correct, please consult       
the Hardware Guide in the Documentation submenu or use the         
(G)eometry command to change it now.                               
                                                                   
Remember: you need to enter whatever your BIOS thinks the         
geometry is!  For IDE, it's what you were told in the BIOS
setup. For SCSI, it's the translation mode your controller is
using.  Do NOT use a ``physical geometry''. 

-----------------------------------------------------------------------

WARNING:  A geometry of 152003/255/63 for amrd1 is incorrect.  Using
a more likely geometry.  If this geometry is incorrect or you
are unsure as to whether or not it's correct, please consult
the Hardware Guide in the Documentation submenu or use the
(G)eometry command to change it now.
           
Remember: you need to enter whatever your BIOS thinks the
geometry is!  For IDE, it's what you were told in the BIOS
setup. For SCSI, it's the translation mode your controller is
using.  Do NOT use a ``physical geometry''.

----------------------------------------------------------------------
V biosu radice jsem zjistil jen celkovou velikost.
572331 MB
1192350 MB



-----------------------------------------------------------------------
Informace o disku amrd0

z programu Diskedit:            z programu Gdisk:
Sectors 1172118402              MB  572331
C   72962                       C   72961
H   255                         H   255
S   63                          S   63
-----------------------------------------------------------------------
Informace o disku amrd1

z programu Diskedit:            z programu Gdisk:
Sectors 2441928132              MB  11923500
C   152004                      C   152003
H   255                         H   255
S   63                          S   63
-----------------------------------------------------------------------




DMESG:
-------------------------------------------------------------------------

Copyright (c) 1992-2005 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 5.4-RELEASE #0: Sun May  8 10:21:06 UTC 2005
    root at harlow.cse.buffalo.edu:/usr/obj/usr/src/sys/GENERIC
ACPI APIC Table: <A M I  OEMAPIC >
Timecounter "i8254" frequency 1193182 Hz quality 0
CPU: Intel(R) Xeon(TM) CPU 3.00GHz (3000.12-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf41  Stepping = 1
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
  Hyperthreading: 2 logical CPUs
real memory  = 3758030848 (3583 MB)
avail memory = 3678216192 (3507 MB)
ioapic0 <Version 2.0> irqs 0-23 on motherboard
ioapic1 <Version 2.0> irqs 24-47 on motherboard
ioapic2 <Version 2.0> irqs 48-71 on motherboard
npx0: <math processor> on motherboard
npx0: INT 16 interface
acpi0: <A M I OEMRSDT> on motherboard
acpi0: Power Button (fixed)
Timecounter "ACPI-fast" frequency 3579545 Hz quality 1000
acpi_timer0: <24-bit timer at 3.579545MHz> port 0x408-0x40b on acpi0
cpu0: <ACPI CPU> on acpi0
pcib0: <ACPI Host-PCI bridge> port 0xcf8-0xcff on acpi0
pci0: <ACPI PCI bus> on pcib0
pcib1: <ACPI PCI-PCI bridge> irq 16 at device 2.0 on pci0
pci1: <ACPI PCI bus> on pcib1
pcib2: <ACPI PCI-PCI bridge> at device 0.0 on pci1
pci3: <ACPI PCI bus> on pcib2
pcib3: <ACPI PCI-PCI bridge> at device 0.2 on pci1
pci2: <ACPI PCI bus> on pcib3
amr0: <LSILogic MegaRAID 1.51> mem 0xfc3f0000-0xfc3fffff irq 53 at device 1.0 on pci2
amr0: <LSILogic MegaRAID SATA 150-6D> Firmware 713N, BIOS G119, 64MB RAM
amr1: <LSILogic MegaRAID 1.51> mem 0xfc3e0000-0xfc3effff irq 55 at device 3.0 on pci2
amr1: <LSILogic MegaRAID SATA 150-6D> Firmware 713N, BIOS G119, 64MB RAM
pcib4: <ACPI PCI-PCI bridge> irq 16 at device 4.0 on pci0
pci4: <ACPI PCI bus> on pcib4
bge0: <Broadcom BCM5721 Gigabit Ethernet, ASIC rev. 0x4101> mem 0xfc8f0000-0xfc8fffff irq 16 at device 0.0 on pci4
miibus0: <MII bus> on bge0
brgphy0: <BCM5750 10/100/1000baseTX PHY> on miibus0
brgphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
bge0: Ethernet address: 00:c0:9f:5d:a5:10
pcib5: <ACPI PCI-PCI bridge> irq 16 at device 5.0 on pci0
pci5: <ACPI PCI bus> on pcib5
bge1: <Broadcom BCM5721 Gigabit Ethernet, ASIC rev. 0x4101> mem 0xfc9f0000-0xfc9fffff irq 16 at device 0.0 on pci5
miibus1: <MII bus> on bge1
brgphy1: <BCM5750 10/100/1000baseTX PHY> on miibus1
brgphy1:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, 1000baseTX, 1000baseTX-FDX, auto
bge1: Ethernet address: 00:c0:9f:5d:a5:11
pcib6: <ACPI PCI-PCI bridge> irq 16 at device 6.0 on pci0
pci6: <ACPI PCI bus> on pcib6
pcib7: <ACPI PCI-PCI bridge> irq 16 at device 7.0 on pci0
pci7: <ACPI PCI bus> on pcib7
uhci0: <Intel 82801EB (ICH5) USB controller USB-A> port 0xe000-0xe01f irq 16 at device 29.0 on pci0
usb0: <Intel 82801EB (ICH5) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801EB (ICH5) USB controller USB-B> port 0xe400-0xe41f irq 19 at device 29.1 on pci0
usb1: <Intel 82801EB (ICH5) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801EB (ICH5) USB controller USB-C> port 0xe800-0xe81f irq 18 at device 29.2 on pci0
usb2: <Intel 82801EB (ICH5) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <Intel 82801EB (ICH5) USB controller USB-D> port 0xec00-0xec1f irq 16 at device 29.3 on pci0
usb3: <Intel 82801EB (ICH5) USB controller USB-D> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
pci0: <serial bus, USB> at device 29.7 (no driver attached)
pcib8: <ACPI PCI-PCI bridge> at device 30.0 on pci0
pci8: <ACPI PCI bus> on pcib8
pci8: <display, VGA> at device 14.0 (no driver attached)
isab0: <PCI-ISA bridge> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH5 SATA150 controller> port 0xfc00-0xfc0f,0x376,0x170-0x177,0x3f6,0x1f0-0x1f7 at device 31.2 on pci0
ata0: channel #0 on atapci0
ata1: channel #1 on atapci0
acpi_button0: <Power Button> on acpi0
atkbdc0: <Keyboard controller (i8042)> port 0x64,0x60 irq 1 on acpi0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model IntelliMouse, device ID 3
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0: port may not be enabled
sio0: <16550A-compatible COM port> port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
sio1: port may not be enabled
sio1: <16550A-compatible COM port> port 0x2f8-0x2ff irq 3 on acpi0
sio1: type 16550A
fdc0: <floppy drive controller (FDE)> port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on acpi0
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
ppc0: <ECP parallel printer port> port 0x778-0x77f,0x378-0x37f irq 7 drq 3 on acpi0
ppc0: Generic chipset (ECP/PS2/NIBBLE) in COMPATIBLE mode
ppc0: FIFO with 16/16/8 bytes threshold
ppbus0: <Parallel port bus> on ppc0
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
orm0: <ISA Option ROMs> at iomem 0xd0000-0xd0fff,0xce800-0xcffff,0xcd000-0xce7ff,0xc0000-0xc7fff on isa0
pmtimer0 on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
Timecounter "TSC" frequency 3000123922 Hz quality 800
Timecounters tick every 10.000 msec
ad0: 190782MB <ST3200822AS/3.01> [387621/16/63] at ata0-master SATA150
amrd0: <LSILogic MegaRAID logical drive> on amr0
amrd0: 572331MB (1172133888 sectors) RAID 5 (optimal)
amrd1: <LSILogic MegaRAID logical drive> on amr1
amrd1: 1192350MB (2441932800 sectors) RAID 5 (optimal)
Mounting root from ufs:/dev/ad0s1a
Previous message: kryptovany filesystem
Next message: OT: Solaris
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
More information about the Users-l mailing list