Chybove hlasky od twe radice

[Bc. Radek Krejča]

Dobry den,

  zacaly se mi v logu objevovat nasledujici hlasky:

  twe0: AEN: <twe0: port 0: sector repair occurred>
  a nekdy
  twe0: AEN: <twe0: port 0: SMART threshold exceeded>

  Mam tento radic se dvema disky v mirroru. O co přesně jde, jedná se
  o hw chybu, či sw chybu?

  Ještě dmesg:

Copyright (c) 1992-2004 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 4.10-STABLE #0: Sun Oct 24 23:26:18 CEST 2004
    root at libuska.starnet.cz:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254"  frequency 1193182 Hz
CPU: Intel(R) Pentium(R) 4 CPU 2.40GHz (2394.01-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf33  Stepping = 3
  Features=0xbfebfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,HTT,TM,PBE>
real memory  = 536018944 (523456K bytes)
avail memory = 516018176 (503924K bytes)
Preloaded elf kernel "kernel" at 0xc0553000.
Warning: Pentium 4 CPU: PSE disabled
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 12 entries at 0xc00f3d30
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
agp0: <Intel 82865 host to AGP bridge> mem 0xff400000-0xff7fffff at device 0.0 on pci0
pcib1: <PCI to PCI bridge (vendor=8086 device=2571)> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
uhci0: <Intel 82801EB (ICH5) USB controller USB-A> port 0xcc00-0xcc1f irq 5 at device 29.0 on pci0
usb0: <Intel 82801EB (ICH5) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <Intel 82801EB (ICH5) USB controller USB-B> port 0xd000-0xd01f irq 3 at device 29.1 on pci0
usb1: <Intel 82801EB (ICH5) USB controller USB-B> on uhci1
usb1: USB revision 1.0
uhub1: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
uhci2: <Intel 82801EB (ICH5) USB controller USB-C> port 0xd400-0xd41f irq 10 at device 29.2 on pci0
usb2: <Intel 82801EB (ICH5) USB controller USB-C> on uhci2
usb2: USB revision 1.0
uhub2: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub2: 2 ports with 2 removable, self powered
uhci3: <Intel 82801EB (ICH5) USB controller USB-D> port 0xd800-0xd81f irq 5 at device 29.3 on pci0
usb3: <Intel 82801EB (ICH5) USB controller USB-D> on uhci3
usb3: USB revision 1.0
uhub3: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub3: 2 ports with 2 removable, self powered
pci0: <USB controller> at 29.7 irq 9
pcib2: <Intel 82801BA/BAM (ICH2) Hub to PCI bridge> at device 30.0 on pci0
pci2: <PCI bus> on pcib2
pci2: <S3 Trio 64V2/DX/GX graphics accelerator> at 0.0 irq 11
twe0: <3ware Storage Controller driver ver. 1.40.01.002> port 0xbc00-0xbc0f mem 0xfe000000-0xfe7fffff,0xfeaefc00-0xfeaefc0f irq 11 at device 2.0 on pci2
twe0: 2 ports, Firmware FE7X 1.05.00.068, BIOS BE7X 1.08.00.048
fxp0: <Intel 82801BA (D865) Pro/100 VE Ethernet> port 0xb800-0xb83f mem 0xfeaee000-0xfeaeefff irq 9 at device 8.0 on pci2
fxp0: Ethernet address 00:11:11:45:ca:24
inphy0: <i82562ET 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
isab0: <PCI to ISA bridge (vendor=8086 device=24d0)> at device 31.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel ICH5 ATA100 controller> port 0xffa0-0xffaf,0-0x3,0-0x7,0-0x3,0-0x7 at device 31.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
atapci1: <Intel ICH5 SATA150 controller> port 0xdc00-0xdc0f,0xe000-0xe003,0xe400-0xe407,0xe800-0xe803,0xec00-0xec07 irq 10 at device 31.2 on pci0
ata2: at 0xec00 on atapci1
ata3: at 0xe400 on atapci1
pci0: <unknown card> (vendor=0x8086, dev=0x24d3) at 31.3 irq 11
pci0: <unknown card> (vendor=0x8086, dev=0x24d5) at 31.5 irq 11
orm0: <Option ROMs> at iomem 0xc0000-0xc7fff,0xc8000-0xc8fff on isa0
pmtimer0 on isa0
fdc0: ready for input in output
fdc0: cmd 3 failed at out byte 1 of 3
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0: configured irq 4 not in bitmap of probed irqs 0
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
twed0: <Unit 0, TwinStor, Normal> on twe0
twed0: 152586MB (312497952 sectors)
Mounting root from ufs:/dev/twed0s1a
twe0: AEN: <twe0: port 0: sector repair occurred>
Limiting icmp unreach response from 202 to 200 packets per second  

-- 
S pozdravem,
 Bc. Radek Krejča
 STARNET, s. r. o.
 radek at ceskedomeny.cz
 http://www.ceskedomeny.cz
 http://www.skdomeny.com
 http://www.starnet.cz