D-Link DSL-360T

[Peter Rosa]

> PPPoE a PPPoA su protokoly a Bridge a Static (?) su mody cinnosti. ked
> bude dsl modem/router v mode Router (tu asi static), moze komunikovat so
> sietou pomocou PPPoE alebo PPPoA. ak je v mode bridge,
> "sprostredkovava" komunikaciu so sietou PC routeru. vtedy musi mat
> PC router nainstalovany protokol PPPoE alebo PPPoA. dali by sa sem poslat
> nastavenia toho modemu/routeru?

OK, ale ktore nastavenia z routeru? Je to FreeBSD 4.10, upravene jadro
(vyhadzane zbytocne zariadenia, firewall), rc.conf nasleduje:
icmp_drop_redirect="YES"
icmp_log_redirect="YES"
tcp_drop_synfin="YES"
tcp_keepalive="YES"
#
gateway_enable="YES"
#defaultrouter="192.168.1.1"
network_interfaces="tl0 rl0 lo0"
ifconfig_tl0="inet 192.168.1.10  netmask 255.255.255.0"
ifconfig_rl0="DHCP"
ifconfig_lo0="inet 127.0.0.1"
#
firewall_enable="YES"
firewall_script="/etc/firewall"
#
local_startup="/usr/local/etc/rc.d"
#
natd_enable="YES"
natd_interface="rl0"
natd_flags="-log_denied -dynamic -use_sockets"

Je treba este dalsie informacie?


Modem ma v tom webovom konfiguraku 4 hlavne zalozky
1. HOME - to je o nicom, zakladny prehlad - Connection...
2. SETUP - dva bloky nastaveni:
    - LAN
        - DHCP server (enable/disable, client range, primary DNS)
    - MODEM SETUP
        - Modulation
        - Connection
            Type: PPPoE, PPPoA, Bridge, Static
            Dalsie nastavenia specificke pre kazdy typ
3. TOOLS - prikazy na ulozenie konfig, restart, reset do tovarenskeho
nastavenia
4. HELP - to je o nicom

Ja mam nastaveny (ako provider kaze) PPPoE, tam su parametre VPI=1, VCI=32,
username/passwd, povolene Set route.

Rezim PPPoA ma podobne parametre ako PPPoE, ale siet Slovanet-u nie je ATM.
Rezim Bridge nema username/passwd, takze asi vytacat bude pppd - skusil som
raz, nespojil sa
Rezim Static som neskusil, tam to chce staticku IP adresu.

Cely manual je na
ftp://ftp.dlink.de/dsl-products/dsl-360t/Manual/dsl-360t_man_eng_040304.pdf
, ale ma to skoro 2MB, takze to asi nikto nebudete chciet citat. Ja mam ten
zazrak techniky doma, a teraz som v praci. Ak to ozaj potrebujete, urobim
screenshoty, dodam zajtra. Ale myslim, ze problem je v routeri, ktory nevie
nieco zapisat do routovacej tabulky a nie v modeme. Modem sa pripoji, ziska
adresu a Slovanet hovori, ze mam zive spojenie. Takze problem je na mojej
strane, nie na ich.

#man 4 arp
...
arpresolve: can't allocate llinfo for %d.%d.%d.%d: The route for the ref-
erenced host points to a device upon which ARP is required, but ARP was
unable to allocate a routing table entry in which to store the host's MAC
address.  This usually points to a misconfigured routing table.  It can
also occur if the kernel cannot allocate memory.
...


Peter Rosa