SpeedTouch USB ADSL

[Zbynek Houska]

On Wed, Jun 02, 2004 at 09:34:56PM +0200, ondra.holecek.bln at centrum.cz wrote:
> tady je ten vypis z dmesg, pouziva to ten ugen, v /dev mam ugen0, ugen0.1, ugen0.5, to s tou tecko jsou jak sem pochopil z manu koncovy body, ale nechapu proc ten pppoa2 chce ugen0.7, kdyz tam mam jen ty tri, :
> 
Ale neposilate dmesg -a ...
> 
> Copyright (c) 1992-2004 The FreeBSD Project.
> Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
> 	The Regents of the University of California. All rights reserved.
> FreeBSD 5.2-RELEASE #0: Sun May  2 01:55:36 GMT 2004
>     bln at custodian.home:/usr/src/sys/i386/compile/CUSTODIAN
> Preloaded elf kernel "/boot/kernel/kernel" at 0xc0a61000.
> Timecounter "i8254" frequency 1193182 Hz quality 0
> CPU: Pentium/P54C (199.43-MHz 586-class CPU)
>   Origin = "GenuineIntel"  Id = 0x52c  Stepping = 12
>   Features=0x1bf<FPU,VME,DE,PSE,TSC,MSR,MCE,CX8>
> real memory  = 82837504 (79 MB)
> avail memory = 68755456 (65 MB)
> Intel Pentium detected, installing workaround for F00F bug
> npx0: [FAST]
> npx0: <math processor> on motherboard
> npx0: INT 16 interface
> pcibios: BIOS version 2.10
> pcib0: <Host to PCI bridge> at pcibus 0 on motherboard
> pci0: <PCI bus> on pcib0
> isab0: <PCI-ISA bridge> at device 7.0 on pci0
> isa0: <ISA bus> on isab0
> atapci0: <Intel PIIX3 WDMA2 controller> port 0xffa0-0xffaf at device 7.1 on pci0
> ata0: at 0x1f0 irq 14 on atapci0
> ata0: [MPSAFE]
> ata1: at 0x170 irq 15 on atapci0
> ata1: [MPSAFE]
> pci0: <memory> at device 12.0 (no driver attached)
> uhci0: <VIA 83C572 USB controller> port 0xff40-0xff5f irq 5 at device 13.0 on pci0
> usb0: <VIA 83C572 USB controller> on uhci0
> usb0: USB revision 1.0
> uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub0: 2 ports with 2 removable, self powered
> uhci1: <VIA 83C572 USB controller> port 0xff80-0xff9f irq 9 at device 13.1 on pci0
> usb1: <VIA 83C572 USB controller> on uhci1
> usb1: USB revision 1.0
> uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
> uhub1: 2 ports with 2 removable, self powered
> ugen0: ALCATEL Speed Touch USB, rev 1.10/0.01, addr 2
> pci0: <serial bus, USB> at device 13.2 (no driver attached)
> pci0: <display, VGA> at device 14.0 (no driver attached)
> wi0: <Intersil Prism2.5> mem 0xfffbe000-0xfffbefff irq 10 at device 15.0 on pci0
> wi0: 802.11 address: 00:60:b3:6e:11:55
> wi0: using RF:PRISM2.5 MAC:ISL3874A(Mini-PCI)
> wi0: Intersil Firmware: Primary (1.0.7), Station (1.3.6)
> wi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
> rl0: <RealTek 8139 10/100BaseTX> port 0xf800-0xf8ff mem 0xfffbfc00-0xfffbfcff irq 11 at device 16.0 on pci0
> rl0: Ethernet address: 00:30:4f:16:c3:7d
> miibus0: <MII bus> on rl0
> rlphy0: <RealTek internal media interface> on miibus0
> rlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
> orm0: <Option ROMs> at iomem 0xed000-0xedfff,0xc0000-0xc7fff on isa0
> pmtimer0 on isa0
> atkbdc0: <Keyboard controller (i8042)> at port 0x64,0x60 on isa0
> fdc0: <Enhanced floppy controller (i82077, NE72065 or clone)> at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
> ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
> ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
> ppbus0: <Parallel port bus> on ppc0
> plip0: <PLIP network interface> on ppbus0
> lpt0: <Printer> on ppbus0
> lpt0: Interrupt-driven port
> ppi0: <Parallel I/O> on ppbus0
> sc0: <System console> at flags 0x100 on isa0
> sc0: VGA <16 virtual consoles, flags=0x300>
> sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
> sio0: type 16550A
> sio1 at port 0x2f8-0x2ff irq 3 on isa0
> sio1: type 16550A
> vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> unknown: <PNP0303> can't assign resources (port)
> unknown: <PNP0700> can't assign resources (port)
> unknown: <PNP0400> can't assign resources (port)
> unknown: <PNP0501> can't assign resources (port)
> unknown: <PNP0501> can't assign resources (port)
> Timecounter "TSC" frequency 199432762 Hz quality 800
> Timecounters tick every 10.000 msec
> ipfw2 initialized, divert enabled, rule-based forwarding enabled, default to deny, logging unlimited
> IPv6 packet filtering initialized, logging limited to 100 packets/entry
> GEOM: create disk ad0 dp=0xc1b81260
> ad0: 4126MB <ST34311A> [8944/15/63] at ata0-master WDMA2
> GEOM: create disk ad1 dp=0xc1b4be60
> ad1: 152627MB <ST3160023A> [310101/16/63] at ata0-slave WDMA2
> acd0: CDROM <TOSHIBA CD-ROM XM-6202B> at ata1-slave PIO4
> Mounting root from ufs:/dev/ad0s1a
> WARNING: / was not properly dismounted
> WARNING: /var was not properly dismounted
> WARNING: /home was not properly dismounted
> WARNING: /backup was not properly dismounted
> ugen0: at uhub1 port 2 (addr 2) disconnected
> ugen0: detached
> ugen0: ALCATEL Speed Touch USB, rev 1.10/0.01, addr 2
> 
Jste si jistej, ze vam bezi usbd? Pac defaultne je vypnutej, ale to jste
si jiste osefoval, ze?
> 
> 
> 
> 
> 
Zbynek
-- 
If you cannot work with love but only with distaste it is better that you
should leave your work.
                                                     Kahlil Gibran