Problem s IDE diskom

[MeX]

podla mojho nazoru je to bud chyba disku alebo kablu - ano, aj to by som 
skontroloval... mne teraz skolaboval novy tzv. okruhly kabel a inak 
vyzera byt opticky v pohode.. to by ma inak zaujimalo, ake mate 
skusenosti s tymito kablami ktore maju inak celkom same vyhody oproti 
klasickym plochym ide kablom? nebola to totiz vynimka. uz sa mi to stalo 
viac krat.

druha vec je ta, ze na 5.x sa myslim stale neodporuca vinum pouzivat v 
produkcnom nasadeni..

MeX
mex at localnet.sk


On 31.5.2004 10:17 , Staniclav Sitar wrote:


> Vazeni pani.
> 
> Nainstaloval som v jednej malej firme velmi jednoduchy fileserver.
> 
> Po skusenostiach s raidom v RedHat Linuxe som tentokrat siahol
> po FreeBSD 5.2.1 a vinum. To je krasa!
> 
> Nainstaloval som "vanilla" FreeBSD 5.2.1 plus samba, mc a Vim.
> 
> Vytvoril som dva zrkadlene Vinum oddiely (volumes).
> Dal som ich zdielat cez Sambu.  Jeden s RW pristupom pre kazdeho a druhy
> ReadOnly. Urobil som maly skript, ktory jeden (maly) adresar na RW oddieli
> kazdu noc o 2:00 zbali to tgz archivu a ulozi na RO oddiel.
> 
> System bezal krasne niekolko dni a potom sa zacali diat veci.
> .........
> ad2: WARNING - READ_DMA UDMA ICRC error (retrying request) LBA=16643886
> .........
> ad2: FAILURE - READ_DMA status=51<READY,DSC,ERROR> 
> error=84<ICRC,ABORTED> LBA=16720430
> vinum: zrkadlo1.p1.s0 is crashed by force
> vinum: zrkadlo1.p1 is faulty
> fatal:zrkadlo1.p1.s0 read error, block 12527465 for 65536 bytes
> zrkadlo1.p1.s0: user buffer block 12527200 for 65536 bytes
> vinum: zrkadlo1.p1.s0 is stale by force
> 
> Disk ad2 je pripojeny na ako master a CDROM je ako slave
> Disk ad2 je presne totozny s ad1 (ad1 je na IDE kabli samostatne)
> 
> Poradte mi prosim.
> Mam reklamovat disk? - ostatne particie zatial zda sa bezia a predpokladam
> ze mi reklamaciu len tak neuznaju.
> Vcera som skopiroval cca 5GB dat z jednej Vinum particie na inu, na 
> ktorej su obidva
> plexy up a jeden ten plex je na tom "podozrivom" disku a ziadna chyba sa
> neprejavila.
> 
> 
> Prikladam kusok zo suboru /var/log/mesages
> 
> ......... System bezi, nic sa nedeje ......
> May 15 22:10:47 server kernel: ep0: Ethernet address 00:50:04:f9:b0:9a
> May 15 22:10:47 server kernel: unknown: <PNP0303> can't assign resources 
> (port)
> May 15 22:10:47 server kernel: unknown: <PNP0a03> can't assign resources 
> (port)
> May 15 22:10:47 server kernel: unknown: <PNP0501> can't assign resources 
> (port)
> May 15 22:10:47 server kernel: unknown: <PNP0700> can't assign resources 
> (port)
> May 15 22:10:47 server kernel: unknown: <PNP0400> can't assign resources 
> (port)
> May 15 22:10:47 server kernel: unknown: <PNP0501> can't assign resources 
> (port)
> May 15 22:10:47 server kernel: Timecounter "TSC" frequency 549064407 Hz 
> quality 800
> May 15 22:10:47 server kernel: Timecounters tick every 10.000 msec
> May 15 22:10:47 server kernel: GEOM: create disk ad0 dp=0xc20a4c60
> May 15 22:10:47 server kernel: ad0: 38166MB <ST340014A> [77545/16/63] at 
> ata0-master UDMA33
> May 15 22:10:47 server kernel: acd0: CDROM <ATAPI 44X CDROM> at 
> ata0-slave PIO4
> May 15 22:10:47 server kernel: GEOM: create disk ad2 dp=0xc20a4360
> May 15 22:10:47 server kernel: ad2: 38166MB <ST340014A> [77545/16/63] at 
> ata1-master UDMA33
> May 15 22:10:47 server kernel: Waiting 15 seconds for SCSI devices to settle
> May 15 22:10:47 server kernel: Mounting root from ufs:/dev/ad0s1a
> May 20 02:00:04 server kernel: ad2: WARNING - READ_DMA UDMA ICRC error 
> (retrying request) LBA=16643886
> May 22 02:00:17 server kernel: ad2: WARNING - READ_DMA UDMA ICRC error 
> (retrying request) LBA=16720046
> May 22 02:00:17 server kernel: ad2: WARNING - READ_DMA UDMA ICRC error 
> (retrying request) LBA=16720046
> May 23 02:00:17 server kernel: ad2: WARNING - READ_DMA UDMA ICRC error 
> (retrying request) LBA=16721518
> May 23 12:31:30 server kernel: ad2: WARNING - READ_DMA UDMA ICRC error 
> (retrying request) LBA=16716070
> May 25 02:00:18 server kernel: ad2: WARNING - READ_DMA UDMA ICRC error 
> (retrying request) LBA=16721134
> May 26 02:00:18 server kernel: ad2: WARNING - READ_DMA UDMA ICRC error 
> (retrying request) LBA=16720430
> May 26 02:00:19 server kernel: ad2: WARNING - READ_DMA UDMA ICRC error 
> (retrying request) LBA=16720430
> May 26 02:00:19 server kernel: ad2: FAILURE - READ_DMA 
> status=51<READY,DSC,ERROR> error=84<ICRC,ABORTED> LBA=16720430
> May 26 02:00:19 server kernel: vinum: zrkadlo1.p1.s0 is crashed by force
> May 26 02:00:19 server kernel: vinum: zrkadlo1.p1 is faulty
> May 26 02:00:19 server kernel: fatal:zrkadlo1.p1.s0 read error, block 
> 12527465 for 65536 bytes
> May 26 02:00:19 server kernel: zrkadlo1.p1.s0: user buffer block 
> 12527200 for 65536 bytes
> May 26 02:00:29 server kernel: vinum: zrkadlo1.p1.s0 is stale by force
> May 29 16:36:55 server login: ROOT LOGIN (root) ON ttyv1
> May 29 16:39:25 server shutdown: reboot by root:
> May 29 16:39:27 server syslogd: exiting on signal 15
> May 29 16:41:25 server syslogd: kernel boot file is /boot/kernel/kernel
> May 29 16:41:25 server kernel: Copyright (c) 1992-2004 The FreeBSD Project.
> May 29 16:41:25 server kernel: Copyright (c) 1979, 1980, 1983, 1986, 
> 1988, 1989, 1991, 1992, 1993, 1994
> May 29 16:41:25 server kernel: The Regents of the University of 
> California. All rights reserved.
> May 29 16:41:25 server kernel: FreeBSD 5.2.1-RELEASE #0: Mon Feb 23 
> 20:45:55 GMT 2004
> May 29 16:41:25 server kernel: 
> root at wv1u.btc.adaptec.com:/usr/obj/usr/src/sys/GENERIC
> May 29 16:41:25 server kernel: Preloaded elf kernel 
> "/boot/kernel/kernel" at 0xc09e3000.
> May 29 16:41:25 server kernel: Timecounter "i8254" frequency 1193182 Hz 
> quality 0
> May 29 16:41:25 server kernel: CPU: Intel Pentium III (549.06-MHz 
> 686-class CPU)
> May 29 16:41:25 server kernel: Origin = "GenuineIntel"  Id = 0x681  
> Stepping = 1
> May 29 16:41:25 server kernel: 
> Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
> May 29 16:41:25 server kernel: real memory  = 134152192 (127 MB)
> May 29 16:41:25 server kernel: avail memory = 120692736 (115 MB)
> May 29 16:41:25 server kernel: Pentium Pro MTRR support enabled
> May 29 16:41:25 server kernel: npx0: [FAST]
> May 29 16:41:25 server kernel: npx0: <math processor> on motherboard
> May 29 16:41:25 server kernel: npx0: INT 16 interface
> May 29 16:41:25 server kernel: pcibios: BIOS version 2.10
> May 29 16:41:25 server kernel: Using $PIR table, 7 entries at 0xc00fda30
> May 29 16:41:25 server kernel: pcib0: <Intel 82443BX (440 BX) host to 
> PCI bridge> at pcibus 0 on motherboard
> May 29 16:41:25 server kernel: pci0: <PCI bus> on pcib0
> May 29 16:41:25 server kernel: pci_cfgintr: 0:7 INTD BIOS irq 11
> May 29 16:41:25 server kernel: pci_cfgintr: 0:12 INTA BIOS irq 10
> May 29 16:41:25 server kernel: agp0: <Intel 82443BX (440 BX) host to PCI 
> bridge> mem 0xe8000000-0xebffffff at device 0.0 on pci0
> May 29 16:41:25 server kernel: pcib1: <PCI-PCI bridge> at device 1.0 on pci0
> May 29 16:41:25 server kernel: pci1: <PCI bus> on pcib1
> May 29 16:41:25 server kernel: pci1: <display, VGA> at device 0.0 (no 
> driver attached)
> May 29 16:41:25 server kernel: isab0: <PCI-ISA bridge> at device 7.0 on pci0
> May 29 16:41:25 server kernel: isa0: <ISA bus> on isab0
> May 29 16:41:25 server kernel: atapci0: <Intel PIIX4 UDMA33 controller> 
> port 0xf000-0xf00f at device 7.1 on pci0
> May 29 16:41:25 server kernel: ata0: at 0x1f0 irq 14 on atapci0
> May 29 16:41:25 server kernel: ata0: [MPSAFE]
> May 29 16:41:25 server kernel: ata1: at 0x170 irq 15 on atapci0
> May 29 16:41:25 server kernel: ata1: [MPSAFE]
> May 29 16:41:25 server kernel: uhci0: <Intel 82371AB/EB (PIIX4) USB 
> controller> port 0xe000-0xe01f irq 11 at device 7.2 on pci0
> May 29 16:41:25 server kernel: usb0: <Intel 82371AB/EB (PIIX4) USB 
> controller> on uhci0
> May 29 16:41:25 server kernel: usb0: USB revision 1.0
> May 29 16:41:25 server kernel: uhub0: Intel UHCI root hub, class 9/0, 
> rev 1.00/1.00, addr 1
> May 29 16:41:25 server kernel: uhub0: 2 ports with 2 removable, self powered
> May 29 16:41:25 server kernel: piix0: <PIIX Timecounter> port 
> 0x5000-0x500f at device 7.3 on pci0
> May 29 16:41:25 server kernel: Timecounter "PIIX" frequency 3579545 Hz 
> quality 0
> May 29 16:41:25 server kernel: ahc0: <Adaptec aic7880 Ultra SCSI 
> adapter> port 0xe400-0xe4ff mem 0xed000000-0xed000fff irq 10 at device 
> 12.0 on pci0
> May 29 16:41:25 server kernel: aic7880: Ultra Wide Channel A, SCSI Id=7, 
> 16/253 SCBs
> May 29 16:41:25 server kernel: orm0: <Option ROM> at iomem 
> 0xc0000-0xc7fff on isa0
> May 29 16:41:25 server kernel: pmtimer0 on isa0
> May 29 16:41:25 server kernel: atkbdc0: <Keyboard controller (i8042)> at 
> port 0x64,0x60 on isa0
> May 29 16:41:25 server kernel: atkbd0: <AT Keyboard> flags 0x1 irq 1 on 
> atkbdc0
> May 29 16:41:25 server kernel: kbd0 at atkbd0
> May 29 16:41:25 server kernel: fdc0: <Enhanced floppy controller 
> (i82077, NE72065 or clone)> at port 0x3f7,0x3f0-0x3f5 irq 6 drq 2 on isa0
> May 29 16:41:25 server kernel: fdc0: FIFO enabled, 8 bytes threshold
> May 29 16:41:25 server kernel: fd0: <1440-KB 3.5" drive> on fdc0 drive 0
> May 29 16:41:25 server kernel: ppc0: <Parallel port> at port 0x378-0x37f 
> irq 7 on isa0
> May 29 16:41:25 server kernel: ppc0: Generic chipset (NIBBLE-only) in 
> COMPATIBLE mode
> May 29 16:41:25 server kernel: ppbus0: <Parallel port bus> on ppc0
> May 29 16:41:25 server kernel: plip0: <PLIP network interface> on ppbus0
> May 29 16:41:25 server kernel: lpt0: <Printer> on ppbus0
> May 29 16:41:25 server kernel: lpt0: Interrupt-driven port
> May 29 16:41:25 server kernel: ppi0: <Parallel I/O> on ppbus0
> May 29 16:41:25 server kernel: sc0: <System console> at flags 0x100 on isa0
> May 29 16:41:25 server kernel: sc0: VGA <16 virtual consoles, flags=0x300>
> May 29 16:41:25 server kernel: sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 
> on isa0
> May 29 16:41:25 server kernel: sio0: type 16550A
> May 29 16:41:25 server kernel: sio1 at port 0x2f8-0x2ff irq 3 on isa0
> May 29 16:41:25 server kernel: sio1: type 16550A
> May 29 16:41:25 server kernel: vga0: <Generic ISA VGA> at port 
> 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
> May 29 16:41:25 server kernel: ep0: <3Com 3C509-TPC EtherLink III> at 
> port 0x220-0x22f irq 5 on isa0
> May 29 16:41:25 server kernel: ep0: Ethernet address 00:50:04:f9:b0:9a
> May 29 16:41:25 server kernel: unknown: <PNP0303> can't assign resources 
> (port)
> May 29 16:41:25 server kernel: unknown: <PNP0a03> can't assign resources 
> (port)
> May 29 16:41:25 server kernel: unknown: <PNP0501> can't assign resources 
> (port)
> May 29 16:41:25 server kernel: unknown: <PNP0700> can't assign resources 
> (port)
> May 29 16:41:25 server kernel: unknown: <PNP0400> can't assign resources 
> (port)
> May 29 16:41:25 server kernel: unknown: <PNP0501> can't assign resources 
> (port)
> May 29 16:41:25 server kernel: Timecounter "TSC" frequency 549064661 Hz 
> quality 800
> May 29 16:41:25 server kernel: Timecounters tick every 10.000 msec
> May 29 16:41:25 server kernel: GEOM: create disk ad0 dp=0xc20a4c60
> May 29 16:41:25 server kernel: ad0: 38166MB <ST340014A> [77545/16/63] at 
> ata0-master UDMA33
> May 29 16:41:25 server kernel: acd0: CDROM <ATAPI 44X CDROM> at 
> ata0-slave PIO4
> May 29 16:41:25 server kernel: GEOM: create disk ad2 dp=0xc20a4360
> May 29 16:41:25 server kernel: ad2: 38166MB <ST340014A> [77545/16/63] at 
> ata1-master UDMA33
> May 29 16:41:25 server kernel: Waiting 15 seconds for SCSI devices to settle
> May 29 16:41:25 server kernel: Mounting root from ufs:/dev/ad0s1a
> May 29 16:41:43 server login: ROOT LOGIN (root) ON ttyv1
> 
> 
> Dakujem
> Stano