pccardd: No free configuration for card
Jan Pechanec
jp at devnull.cz
Mon May 10 12:08:43 CEST 2004
ahoj, nezkousel jste nahodou nekdo nekdy 2 stejne PCMCIA karty
(sitovky) v jednom boxu? Posilal jsem mail do -stable, ale zadna
odezva. Posilam to, co jsem tam psal, treba by mi nekdo mohl pomoct.
Zacit se zabyvat zdrojakem je pro me spis ta posledni moznost. V
dostupnych archivech jsem nic nenasel. diky, h.
Hi, I'm testing two 16-bit ethernet PCMCIA cards SMC
8041TX-10/100-PC-Card-V2 in Soekris 4521 box. Using 4.9-RELEASE-p7
with ed driver in the kernel. I added a new section to
/etc/pccard.conf:
card "SMC" "8041TX-10/100-PC-Card-V2"
config auto "ed" ?
insert /etc/pccard_ether $device start
remove /etc/pccard_ether $device stop
and the card works fine, but the 2nd card is not accepted:
May 6 23:06:34 openrouter pccardd[365]: No free configuration for card SMC
I'm looking into the code for pccardd and it seems to me that
"Found existing driver" message from assign_driver() should appear (I
increased the debug level) when I insert the 2nd card, but it doesn't.
Any help, please? Full console output follows:
root at openrouter.idc.cz:~# pccard: card inserted, slot 0
May 7 00:32:09 openrouter pccardd[547]: Card "SMC"("8041TX-10/100-PC-Card-V2") [] [[none]] matched "SMC" ("8041TX-10/100-PC-Card-V2") [(null)] [(null)]
May 7 00:32:09 openrouter pccardd[547]: Using I/O addr 0x240, size 32
May 7 00:32:09 openrouter pccardd[547]: Setting config reg at offs 0x3f8 to 0x60, Reset time = 50 ms
May 7 00:32:14 openrouter pccaredd[547]: Assignidng I/O window 0,0 start 0x240, si ze 0x20 flags 0xa7
tMay 7 00:32:14 openrouter pccarpdd[547]: Assign oed-1, io 0x240-0rx25f, mem 0x0, 0t bytes, irq 10, flag0s 0x240-0x25f irq 10 slot 0 on pccard0
ed0: address 00:04:e2:a3:26:25, type NE2000 (16 bit)
May 7 00:32:14 openrouter pccardd[547]: ed0: SMC (8041TX-10/100-PC-Card-V2) inserted.
pccard: card inserted, slot 1
May 7 00:32:46 openrouter pccardd[547]:CCard "SMC"("8041TX-10/100-PC-Card-V2") [] [[none]] matched "SMC" ("8041TX-10/100-PC-Card-V2") [(null)] [(null)]
May 7 00:32:46 openrouter pccardd[547]: No free configuration for card SMC
pccardc dumpcis:
Configuration data for card in slot 0
Tuple #1, code = 0x1 (Common memory descriptor), length = 3
000: 49 00 ff
Common memory device information:
Device number 1, type EEPROM, WPS = ON
Speed = 250nS, Memory block size = 512b, 1 units
Tuple #2, code = 0x15 (Version 1 info), length = 33
000: 04 01 53 4d 43 00 38 30 34 31 54 58 2d 31 30 2f
010: 31 30 30 2d 50 43 2d 43 61 72 64 2d 56 32 00 00
020: ff
Version = 4.1, Manuf = [SMC], card vers =
[8041TX-10/100-PC-Card-V2]
Addit. info = []
Tuple #3, code = 0x20 (Manufacturer ID), length = 4
000: bf 01 41 80
PCMCIA ID = 0x1bf, OEM ID = 0x8041
Tuple #4, code = 0x1a (Configuration map), length = 5
000: 01 27 f8 03 03
Reg len = 2, config register addr = 0x3f8, last config = 0x27
Registers: XX------
Tuple #5, code = 0x1b (Configuration entry), length = 17
000: e0 81 1d 3f 55 4d 5d 06 86 46 26 fc 24 65 30 fc
010: be
Config index = 0x20(default)
Interface byte = 0x81 (I/O) wait signal supported
Vcc pwr:
Nominal operating supply voltage: 5 x 1V
Minimum operating supply voltage: 4.5 x 1V
Maximum operating supply voltage: 5.5 x 1V
Continuous supply current: 1 x 100mA
Max current average over 1 second: 1 x 100mA, ext = 0x46
Max current average over 10 ms: 2 x 100mA
Wait scale Speed = 1.5 x 10 us
Card decodes 5 address lines, full 8/16 Bit I/O
IRQ modes: Level
IRQs: 2 3 4 5 6 7 9 10 11 12 13 15
Tuple #6, code = 0x1b (Configuration entry), length = 7
000: 20 08 ca 60 20 03 1f
Config index = 0x20
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x320 block length = 0x20
Tuple #7, code = 0x1b (Configuration entry), length = 7
000: 21 08 ca 60 40 03 1f
Config index = 0x21
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x340 block length = 0x20
Tuple #8, code = 0x1b (Configuration entry), length = 7
000: 22 08 ca 60 60 03 1f
Config index = 0x22
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x360 block length = 0x20
Tuple #9, code = 0x1b (Configuration entry), length = 7
000: 23 08 ca 60 80 02 1f
Config index = 0x23
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x280 block length = 0x20
Tuple #10, code = 0x1b (Configuration entry), length = 7
000: 24 08 ca 60 60 02 1f
Config index = 0x24
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x260 block length = 0x20
Tuple #11, code = 0x1b (Configuration entry), length = 7
000: 25 08 ca 60 40 02 1f
Config index = 0x25
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x240 block length = 0x20
Tuple #12, code = 0x1b (Configuration entry), length = 7
000: 26 08 ca 60 20 02 1f
Config index = 0x26
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x220 block length = 0x20
Tuple #13, code = 0x1b (Configuration entry), length = 7
000: 27 08 ca 60 00 02 1f
Config index = 0x27
Card decodes 10 address lines, limited 8/16 Bit I/O
I/O address # 1: block start = 0x200 block length = 0x20
Tuple #14, code = 0x21 (Functional ID), length = 2
000: 06 00
Network/LAN adapter
Tuple #15, code = 0x14 (No link), length = 0
Tuple #16, code = 0xff (Terminator), length = 0
thanks, Jan.
--
Jan Pechanec <jp (at) devnull (dot) cz>
_______________________________________________
Soekris-tech mailing list
Soekris-tech at lists.soekris.com
http://lists.soekris.com/mailman/listinfo/soekris-tech
More information about the Users-l
mailing list