USBFlashDisk 2

Pavlicek Jaroslav Ing. Jaroslav_Pavlicek at kb.cz
Wed Feb 4 16:09:57 CET 2004
Previous message: IDE DEAD
Next message: verzia perlu
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
A jinak Ti propojovani / odpojovani USB zarizeni chodi (mys, tiskarna ...),
tim stylem, ze si to vsimne, ze byli pripojeni / odpojeni ? Bezi Ti deameno
usbd ?

--- Jara


-----Original Message-----
From: Ornell [mailto:fedajkin at centrum.cz] 
Sent: Wednesday, February 04, 2004 3:45 PM
To: FreeBSD mailing list
Subject: Re: USBFlashDisk 2


Sakra i podavat dotazy se musi clovek ucit  :))))
takze: nejsem schopen pristoupit k USB flash disku kdyz ho pripojim za 
chodu, pouze pokud startuji system s pripojenym USB diskem tak to jde si 
ho potom mountnout z /dev/da0s1. Pokud system nastartuji s USB diskem 
pouziji vytahnu a potom znovu pripojim a chci mountnout zahlasi mi to 
/dev/da0s1 Input/output error. Pokud system nastartuji bez USB disku a 
chci moutnout system zahlasi /dev/da0s1 Device not configured. Netusim 
co delam spatne moduly nahrane mam tak vas prosim o pomoc.

Na zaver propojuji dmesg s USB diskem a bez.

s pripojenym USB diskem

FreeBSD 4.9-RELEASE #0: Mon Oct 27 17:51:09 GMT 2003
     root at freebsd-stable.sentex.ca:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254"  frequency 1193182 Hz
CPU: AMD Duron(tm) processor (850.04-MHz 686-class CPU)
   Origin = "AuthenticAMD"  Id = 0x631  Stepping = 1
 
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,
PAT,PSE36,MMX,FXSR>
   AMD Features=0xc0440000<RSVD,AMIE,DSP,3DNow!>
real memory  = 259981312 (253888K bytes)
config> di bt0
config> di aic0
config> di aha0
config> di adv0
config> en ed0
config> po ed0 0x280
config> ir ed0 10
config> iom ed0 0xd8000
config> f ed0 0
config> q
avail memory = 247279616 (241484K bytes)
Preloaded elf kernel "kernel" at 0xc0588000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc058809c. Preloaded elf
module "snd_via82c686.ko" at 0xc05880ec. Preloaded elf module "snd_pcm.ko"
at 0xc0588194. Preloaded elf module "usb.ko" at 0xc0588234. Preloaded elf
module "umass.ko" at 0xc05882d0. Preloaded elf module "uscanner.ko" at
0xc0588370. Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 6 entries at 0xc00fdb60
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
agp0: <VIA Generic host to PCI bridge> mem 0xd0000000-0xd3ffffff at 
device 0.0 on pci0
pcib1: <PCI to PCI bridge (vendor=1106 device=b112)> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <Trident model 8500 VGA-compatible display device> at 0.0 irq 10
isab0: <VIA 82C686 PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C686 ATA100 controller> port 0xd000-0xd00f at device 7.1 
on pci0
atapci0: Correcting VIA config for southbridge data corruption bug
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <VIA 83C572 USB controller> port 0xd400-0xd41f irq 9 at device 
7.2 on pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <VIA 83C572 USB controller> port 0xd800-0xd81f irq 9 at device 
7.3 on pci0
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
ugen0: Hewlett-Packard HP Scanjet 5400C Series, rev 1.10/0.00, addr 2
umass0: 3SYSTEM USB FLASH DISK, rev 1.10/1.00, addr 3
pci0: <unknown card> (vendor=0x1106, dev=0x3057) at 7.4
pcm0: <VIA VT82C686A> port 0xe400-0xe403,0xe000-0xe003,0xdc00-0xdcff irq 
3 at device 7.5 on pci0
pcm0: <Realtek ALC100 AC97 Codec>
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xec00-0xec7f mem 
0xd8000000-0xd800007f irq 11 at device 9.0 on pci0
xl0: Ethernet address: 00:04:76:d1:a9:0f
miibus0: <MII bus> on xl0
xlphy0: <3c905C 10/100 internal PHY> on miibus0
xlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
orm0: <Option ROMs> at iomem 0xc0000-0xcbfff,0xcc000-0xcc7ff on isa0
pmtimer0 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model NetMouse/NetScroll Optical, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ad0: 19092MB <WDC WD200EB-00CSF0> [38792/16/63] at ata0-master UDMA100
ad1: 19607MB <QUANTUM FIREBALLP AS20.5> [39838/16/63] at ata0-slave UDMA100
acd0: CDROM <CD-ROM 52X/AKH> at ata1-slave PIO4
Mounting root from ufs:/dev/ad0s1a
da0 at umass-sim0 bus 0 target 0 lun 0
da0: <3SYSTEM USB FLASH DISK 1.00> Removable Direct Access SCSI-2 device
da0: 650KB/s transfers
da0: 105MB (215040 512 byte sectors: 64H 32S/T 105C)

a bez pripojeneho USB disku

FreeBSD 4.9-RELEASE #0: Mon Oct 27 17:51:09 GMT 2003
     root at freebsd-stable.sentex.ca:/usr/obj/usr/src/sys/GENERIC
Timecounter "i8254"  frequency 1193182 Hz
CPU: AMD Duron(tm) processor (850.04-MHz 686-class CPU)
   Origin = "AuthenticAMD"  Id = 0x631  Stepping = 1
 
Features=0x183f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,
PAT,PSE36,MMX,FXSR>
   AMD Features=0xc0440000<RSVD,AMIE,DSP,3DNow!>
real memory  = 259981312 (253888K bytes)
config> di bt0
config> di aic0
config> di aha0
config> di adv0
config> en ed0
config> po ed0 0x280
config> ir ed0 10
config> iom ed0 0xd8000
config> f ed0 0
config> q
avail memory = 247279616 (241484K bytes)
Preloaded elf kernel "kernel" at 0xc0588000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc058809c. Preloaded elf
module "snd_via82c686.ko" at 0xc05880ec. Preloaded elf module "snd_pcm.ko"
at 0xc0588194. Preloaded elf module "usb.ko" at 0xc0588234. Preloaded elf
module "umass.ko" at 0xc05882d0. Preloaded elf module "uscanner.ko" at
0xc0588370. Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 6 entries at 0xc00fdb60
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
agp0: <VIA Generic host to PCI bridge> mem 0xd0000000-0xd3ffffff at 
device 0.0 on pci0
pcib1: <PCI to PCI bridge (vendor=1106 device=b112)> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <Trident model 8500 VGA-compatible display device> at 0.0 irq 10
isab0: <VIA 82C686 PCI-ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <VIA 82C686 ATA100 controller> port 0xd000-0xd00f at device 7.1 
on pci0
atapci0: Correcting VIA config for southbridge data corruption bug
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <VIA 83C572 USB controller> port 0xd400-0xd41f irq 9 at device 
7.2 on pci0
usb0: <VIA 83C572 USB controller> on uhci0
usb0: USB revision 1.0
uhub0: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
uhci1: <VIA 83C572 USB controller> port 0xd800-0xd81f irq 9 at device 
7.3 on pci0
usb1: <VIA 83C572 USB controller> on uhci1
usb1: USB revision 1.0
uhub1: VIA UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub1: 2 ports with 2 removable, self powered
ugen0: Hewlett-Packard HP Scanjet 5400C Series, rev 1.10/0.00, addr 2
pci0: <unknown card> (vendor=0x1106, dev=0x3057) at 7.4
pcm0: <VIA VT82C686A> port 0xe400-0xe403,0xe000-0xe003,0xdc00-0xdcff irq 
3 at device 7.5 on pci0
pcm0: <Realtek ALC100 AC97 Codec>
xl0: <3Com 3c905C-TX Fast Etherlink XL> port 0xec00-0xec7f mem 
0xd8000000-0xd800007f irq 11 at device 9.0 on pci0
xl0: Ethernet address: 00:04:76:d1:a9:0f
miibus0: <MII bus> on xl0
xlphy0: <3c905C 10/100 internal PHY> on miibus0
xlphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
orm0: <Option ROMs> at iomem 0xc0000-0xcbfff,0xcc000-0xcc7ff on isa0
pmtimer0 on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> flags 0x1 irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model NetMouse/NetScroll Optical, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (EPP/NIBBLE) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
ad0: 19092MB <WDC WD200EB-00CSF0> [38792/16/63] at ata0-master UDMA100
ad1: 19607MB <QUANTUM FIREBALLP AS20.5> [39838/16/63] at ata0-slave UDMA100
acd0: CDROM <CD-ROM 52X/AKH> at ata1-slave PIO4
Mounting root from ufs:/dev/ad0s1a

-- 
FreeBSD mailing list (users-l at freebsd.cz)
http://www.freebsd.cz/listserv/listinfo/users-l
Previous message: IDE DEAD
Next message: verzia perlu
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]
More information about the Users-l mailing list