Problem s usbd

[adam]

On Wed, Jun 25, 2003 at 08:16:41AM +0200, Zbynek Houska wrote:
> Dobry den,
> 
>   stala se mi jedna zvalstni vec. Na mem stroji s 4.8 RELEASE mi nejde
> pripojit usb zip 100 mb mechanika. Pred casem jsem tam mel jeste 5.0 REL. a
> tam bylo vse v poradku.

Pridam se se svym problemem taktez mam notebook (FS Lifebook) s USB, v
Linuxu a Win98 je vse vpohode ale v 4.8-STABLE mam s usb problem viz. cast
dmesg (cely je vypsan nize)

uhci0: <Intel 82371AB/EB (PIIX4) USB controller> irq 9 at device 7.2 on pci0
uhci0: Could not map ports
device_probe_and_attach: uhci0 attach returned 6

Pak samozrejme kdyz chci spustit usbd napise mi to:

No USB host controllers found


S irq jsem uz ruzne cachoval ale nic (v linuxu a v M$shit to vzdy jede :-(
).


			Adam


Dmesg:
Copyright (c) 1992-2003 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 4.8-RC #12: Sun May 18 19:30:49 CEST 2003
    adam at snoopy.i.cz:/usr/src/sys/compile/ADAM
Timecounter "i8254"  frequency 1193182 Hz
CPU: Intel Celeron (547.31-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0x683  Stepping = 3
  Features=0x383f9ff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,MMX,FXSR,SSE>
real memory  = 335478784 (327616K bytes)
avail memory = 321363968 (313832K bytes)
Preloaded elf kernel "kernel" at 0xc0495000.
Preloaded userconfig_script "/boot/kernel.conf" at 0xc049509c.
Preloaded elf module "agp.ko" at 0xc04950ec.
netsmb_dev: loaded
Pentium Pro MTRR support enabled
md0: Malloc disk
Using $PIR table, 7 entries at 0xc00fdf50
apm0: <APM BIOS> on motherboard
apm0: found APM BIOS v1.2, connected at v1.2
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Intel 82443BX (440 BX) host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
agp0: <Intel 82443BX (440 BX) host to PCI bridge> mem 0xe0000000-0xe3ffffff at device 0.0 on pci0
pcib1: <Intel 82443BX (440 BX) PCI-PCI (AGP) bridge> at device 1.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <ATI Mobility-1 graphics accelerator> at 0.0 irq 9
pci_cfgintr_virgin: using routable interrupt 10
pci_cfgintr: 0:4 INTA routed to irq 10
pcic0: <TI PCI-1420 PCI-CardBus Bridge> irq 10 at device 4.0 on pci0
pcic0: PCI Memory allocated: 0x88000000
pcic0: TI12XX PCI Config Reg: [speaker enable][pwr save][FUNC pci int + CSC serial isa irq]
pccard0: <PC Card 16-bit bus (classic)> on pcic0
pci_cfgintr_virgin: using routable interrupt 10
pci_cfgintr: 0:4 INTA routed to irq 10
pcic1: <TI PCI-1420 PCI-CardBus Bridge> irq 10 at device 4.1 on pci0
pcic1: PCI Memory allocated: 0x88001000
pcic1: TI12XX PCI Config Reg: [speaker enable][pwr save][FUNC pci int + CSC serial isa irq]
pccard1: <PC Card 16-bit bus (classic)> on pcic1
isab0: <Intel 82371AB PCI to ISA bridge> at device 7.0 on pci0
isa0: <ISA bus> on isab0
atapci0: <Intel PIIX4 ATA33 controller> port 0x1080-0x108f at device 7.1 on pci0
ata0: at 0x1f0 irq 14 on atapci0
ata1: at 0x170 irq 15 on atapci0
uhci0: <Intel 82371AB/EB (PIIX4) USB controller> irq 9 at device 7.2 on pci0
uhci0: Could not map ports
device_probe_and_attach: uhci0 attach returned 6
chip0: <Intel 82371AB Power management controller> port 0xff80-0xff8f at device 7.3 on pci0
pcm0: <Crystal Semiconductor CS4281> mem 0xfc110000-0xfc11ffff,0xfc101000-0xfc101fff irq 5 at device 8.0 on pci0
pcm0: <Cirrus Logic CS4297B ac97 codec>
pci0: <unknown card> (vendor=0x11c1, dev=0x0450) at 16.0 irq 9
fxp0: <Intel Pro 10/100B/100+ Ethernet> port 0x1040-0x107f mem 0xfc000000-0xfc0fffff,0xfc100000-0xfc100fff irq 9 at device 17.0 on pci0
fxp0: Ethernet address 00:90:96:09:e3:27
inphy0: <i82555 10/100 media interface> on miibus0
inphy0:  10baseT, 10baseT-FDX, 100baseTX, 100baseTX-FDX, auto
pci0: <unknown card> (vendor=0x0000, dev=0x0000) at 17.1 irq 9
orm0: <Option ROM> at iomem 0xc0000-0xcffff on isa0
fdc0: <NEC 72065B or clone> at port 0x3f0-0x3f5,0x3f7 irq 6 drq 2 on isa0
fdc0: FIFO enabled, 8 bytes threshold
fd0: <1440-KB 3.5" drive> on fdc0 drive 0
atkbdc0: <Keyboard controller (i8042)> at port 0x60,0x64 on isa0
atkbd0: <AT Keyboard> irq 1 on atkbdc0
kbd0 at atkbd0
psm0: <PS/2 Mouse> irq 12 on atkbdc0
psm0: model NetMouse/NetScroll Optical, device ID 0
vga0: <Generic ISA VGA> at port 0x3c0-0x3df iomem 0xa0000-0xbffff on isa0
sc0: <System console> at flags 0x100 on isa0
sc0: VGA <16 virtual consoles, flags=0x300>
sio0 at port 0x3f8-0x3ff irq 4 flags 0x10 on isa0
sio0: type 16550A
sio1: configured irq 3 not in bitmap of probed irqs 0
ppc0: <Parallel port> at port 0x378-0x37f irq 7 on isa0
ppc0: Generic chipset (NIBBLE-only) in COMPATIBLE mode
plip0: <PLIP network interface> on ppbus0
lpt0: <Printer> on ppbus0
lpt0: Interrupt-driven port
ppi0: <Parallel I/O> on ppbus0
pccard: card inserted, slot 0
pccard: card removed, slot 0
ad0: 9590MB <TOSHIBA MK1016GAP> [19485/16/63] at ata0-master UDMA33
acd0: CDROM <CD-224E> at ata1-master PIO4
pccard: card inserted, slot 0
Mounting root from ufs:/dev/ad0s2a
cd0 at ata1 bus 0 target 0 lun 0
cd0: <TEAC CD-224E 1.7A> Removable CD-ROM SCSI-0 device 
cd0: 16.000MB/s transfers
cd0: Attempt to query device size failed: NOT READY, Medium not present
sio4 at port 0x2f8-0x2ff irq 10 flags 0x40000 slot 0 on pccard0
sio4: type 16550A
sio4: unable to activate interrupt in fast mode - using normal mode