AIC 7902 na Super Micro P4DP8 G2

[Josef Jursa]

Dobry den,

mam problem s radicem AIC 7902 integrovanym na desce Super Micro P4DP8 G2
- FReeFSD 4.7 (Pro RedHat 7.3 mam ovladace a vse bezi). Detekuje se
kupodivu jako 7901A. Prikladam vypis - dmesg (PCI sloty jsou prazdne - vse
je onboard). I kdyz radic na boardu vypnu, hlasky typu:

pci0: <unknown card> (vendor=0x8086, dev=0x2541) at 0.1

zustavaji - viz priloha (vse co zacina ahd0 samozrejme zmizi).

Napada Vas nekoho co s tim?

Zdravi Josef Jursa

dmesg:

Copyright (c) 1992-2002 The FreeBSD Project.
Copyright (c) 1979, 1980, 1983, 1986, 1988, 1989, 1991, 1992, 1993, 1994
        The Regents of the University of California. All rights reserved.
FreeBSD 4.7-RELEASE-p2 #0: Mon Nov 18 16:29:42 CET 2002
    root at orel.ibp.cz:/usr/src/sys/compile/IVO
Timecounter "i8254"  frequency 1193182 Hz
CPU: Pentium 4 (2399.74-MHz 686-class CPU)
  Origin = "GenuineIntel"  Id = 0xf24  Stepping = 4

Features=0x3febfbff<FPU,VME,DE,PSE,TSC,MSR,PAE,MCE,CX8,APIC,SEP,MTRR,PGE,MCA,CMOV,PAT,PSE36,CLFLUSH,DTS,ACPI,MMX,FXSR,SSE,SSE2,SS,<b28>,ACC>
real memory  = 536346624 (523776K bytes)
avail memory = 513404928 (501372K bytes)
Preloaded elf kernel "kernel" at 0xc0820000.
Preloaded mfs_root "/mfsroot" at 0xc082009c.
Pentium Pro MTRR support enabled
md0: Preloaded image </mfsroot> 4423680 bytes at 0xc03e6e0c
md1: Malloc disk
Using $PIR table, 29 entries at 0xc00fddf0
npx0: <math processor> on motherboard
npx0: INT 16 interface
pcib0: <Host to PCI bridge> on motherboard
pci0: <PCI bus> on pcib0
pci0: <unknown card> (vendor=0x8086, dev=0x2541) at 0.1
pcib1: <PCI to PCI bridge (vendor=8086 device=2543)> at device 2.0 on pci0
pci1: <PCI bus> on pcib1
pci1: <unknown card> (vendor=0x8086, dev=0x1461) at 28.0
pcib2: <PCI to PCI bridge (vendor=8086 device=1460)> at device 29.0 on
pci1
pci2: <PCI bus> on pcib2
pci1: <unknown card> (vendor=0x8086, dev=0x1461) at 30.0
pcib3: <PCI to PCI bridge (vendor=8086 device=1460)> at device 31.0 on
pci1
pci3: <PCI bus> on pcib3
em0: <Intel(R) PRO/1000 Network Connection, Version - 1.3.14> port
0x3000-0x303f mem 0xfc200000-0xfc21ffff irq 11 at device 2.0 on pci3
em0:  Speed:100 Mbps  Duplex:Full
em1: <Intel(R) PRO/1000 Network Connection, Version - 1.3.14> port
0x3040-0x307f mem 0xfc220000-0xfc23ffff irq 11 at device 2.1 on pci3
em1:  Speed:N/A  Duplex:N/A
pcib4: <PCI to PCI bridge (vendor=8086 device=2545)> at device 3.0 on pci0
pci4: <PCI bus> on pcib4
pci4: <unknown card> (vendor=0x8086, dev=0x1461) at 28.0
pcib5: <PCI to PCI bridge (vendor=8086 device=1460)> at device 29.0 on
pci4
pci5: <PCI bus> on pcib5
pci4: <unknown card> (vendor=0x8086, dev=0x1461) at 30.0
pcib6: <PCI to PCI bridge (vendor=8086 device=1460)> at device 31.0 on
pci4
pci6: <PCI bus> on pcib6
ahd0: <Adaptec 7901A Ultra320 SCSI adapter> port
0x4000-0x40ff,0x4400-0x44ff mem 0xfc400000-0xfc401fff irq 11 at device 2.0
on pci6
ahd0: scb size = 0x4c, hscb size - 0x40
ahd0: WARNING - Failed chip reset!  Trying to initialize anyway.
ahd0: Primary Auto-Term Sensing failed! Using Defaults.
ahd0: Secondary Auto-Term Sensing failed! Using Defaults.
ahd0: Unable to set termination settings!
ahd0: No SCB space found
device_probe_and_attach: ahd0 attach returned 12
ahd0: <Adaptec 7901A Ultra320 SCSI adapter> port
0x4800-0x48ff,0x4c00-0x4cff mem 0xfc402000-0xfc403fff irq 11 at device 2.1
on pci6
ahd0: scb size = 0x4c, hscb size - 0x40
ahd0: WARNING - Failed chip reset!  Trying to initialize anyway.
ahd0: Primary Auto-Term Sensing failed! Using Defaults.
ahd0: Secondary Auto-Term Sensing failed! Using Defaults.
ahd0: Unable to set termination settings!
ahd0: No SCB space found
device_probe_and_attach: ahd0 attach returned 12
uhci0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> port 0x2000-0x201f
irq 11 at device 29.0 on pci0
usb0: <Intel 82801CA/CAM (ICH3) USB controller USB-A> on uhci0
usb0: USB revision 1.0
uhub0: Intel UHCI root hub, class 9/0, rev 1.00/1.00, addr 1
uhub0: 2 ports with 2 removable, self powered
 .
 .
 .
ahd0: <Adaptec 7901A Ultra320 SCSI adapter> port
0x4000-0x40ff,0x4400-0x44ff mem 0xfc400000-0xfc401fff irq 11 at device 2.0
on pci6
ahd0: scb size = 0x4c, hscb size - 0x40
ahd0: WARNING - Failed chip reset!  Trying to initialize anyway.
ahd0: Primary Auto-Term Sensing failed! Using Defaults.
ahd0: Secondary Auto-Term Sensing failed! Using Defaults.
ahd0: Unable to set termination settings!
ahd0: No SCB space found
device_probe_and_attach: ahd0 attach returned 12
ahd0: <Adaptec 7901A Ultra320 SCSI adapter> port
0x4800-0x48ff,0x4c00-0x4cff mem 0xfc402000-0xfc403fff irq 11 at device 2.1
on pci6
ahd0: scb size = 0x4c, hscb size - 0x40
ahd0: WARNING - Failed chip reset!  Trying to initialize anyway.
ahd0: Primary Auto-Term Sensing failed! Using Defaults.
ahd0: Secondary Auto-Term Sensing failed! Using Defaults.
ahd0: Unable to set termination settings!
ahd0: No SCB space found
device_probe_and_attach: ahd0 attach returned 12
module_register: module pci/mlx already exists!
linker_file_sysinit "mlx.ko" failed to register! 17
module_register: module pci/amr already exists!
linker_file_sysinit "amr.ko" failed to register! 17
module_register: module pci/twe already exists!
linker_file_sysinit "twe.ko" failed to register! 17
module_register: module pci/mly already exists!
linker_file_sysinit "mly.ko" failed to register! 17
ahd0: <Adaptec 7901A Ultra320 SCSI adapter> port
0x4000-0x40ff,0x4400-0x44ff mem 0xfc400000-0xfc401fff irq 11 at device 2.0
on pci6
ahd0: scb size = 0x4c, hscb size - 0x40
ahd0: WARNING - Failed chip reset!  Trying to initialize anyway.
ahd0: Primary Auto-Term Sensing failed! Using Defaults.
ahd0: Secondary Auto-Term Sensing failed! Using Defaults.
ahd0: Unable to set termination settings!
ahd0: No SCB space found
device_probe_and_attach: ahd0 attach returned 12
ahd0: <Adaptec 7901A Ultra320 SCSI adapter> port
0x4800-0x48ff,0x4c00-0x4cff mem 0xfc402000-0xfc403fff irq 11 at device 2.1
on pci6
ahd0: scb size = 0x4c, hscb size - 0x40
ahd0: WARNING - Failed chip reset!  Trying to initialize anyway.
ahd0: Primary Auto-Term Sensing failed! Using Defaults.
ahd0: Secondary Auto-Term Sensing failed! Using Defaults.
ahd0: Unable to set termination settings!
ahd0: No SCB space found
device_probe_and_attach: ahd0 attach returned 12