upsd

[pkodl at ra.rockwell.com]

>tak jsem se konecne dostal ke konfiguraci upsd. A at delam co delam, upsd
>mi stale vypisuje hlasku, ze nemuze dostat moji UPSku do Smart mode.
>Tak premyslim co s tim.
>Pomuzete mi nekdo?
>UPSka je SmatrUPS APC-900

pokud si dobre vzpominam, jadro pulda je v upsd.conf

posilam jeden, kterej nam funguje s APC Smart-UPS 700

===========================================================================
=================

# $Id: upsd.conf,v 1.1.1.1 1998/02/25 16:46:24 steve Exp $
#
# UPS Daemon
# The Wild Wind Communications, 1995, 1996
#
# See file LICENSE for the distribution terms of this software.
#

ups "smart-ups" (230) proto "apc-smart" {
     device              "/dev/cuaa0"
     speed               2400
     read-timeout        2
     write-block-size    1
     write-block-delay   50
     queue-size          64
}

every 5 { # check events every 5 seconds
     nop
}

on "initialize" != "SM" {
     poll "initialize"
     after 60 every 60 {
          log emerg "Cannot put the UPS into smart mode!"
     }
}

every 600 {
     tune "high-transfer-point"          264
     tune "low-transfer-point"           196
     tune "line-alarm"             "0"
     tune "line-sensitivity"             "L"
     tune "low-batteries-duration"       2
     tune "nominal-voltage"              220
     tune "shutdown-delay"               20
     tune "wakeup-batteries-capacity"    25
     tune "wakeup-delay"           0
#    tune "batteries-replaced"           "01/01/77"
#    tune "label"                  "WildWind"
}

every 300 {              # poll the UPS
     poll "last-test"
#    poll "light-test"
     poll "line-frequency"
     poll "line-maxvac"
     poll "line-minvac"
     poll "line-voltage"
     poll "load"
     poll "recharge"
     poll "temperature"
     poll "vdc"
     poll "voltage"

     log notice "last test: %last-test%, light test: %light-test%"
     log notice "frequency: %line-frequency%, maxvac: %line-maxvac%,
minvac: %line-minvac%, voltage: %line-voltage%"
     log notice "load: %load%, recharge: %recharge%, temp: %temperature%,
vdc: %vdc%, output voltage: %voltage%"

     on "load" > 95 {
          log alert "UPS load is too high: %load%"
     }
}

on "line-fail" {
     log emerg "*** ALERT! Source power line failed, save your work! ***"
}

on "line-fail" after 30 {
     log emerg "*** ALERT! System shutdown in 30 seconds, LOGOUT NOW! ***"
}

on "line-restore" {
     log emerg "Source power line restored, you may continue your work."
}

on "line-fail" after 60 {
     log emerg "*** ALERT! THE SYSTEM IS SHUTTING DOWN! ***"

     poll "shutdown"
     poll "shutdown"
     poll "power-test"
     poll "power-test"
     poll "shutdown"
     poll "shutdown"

     sleep 2

     exec "/sbin/halt &"

     poll "power-test"
     poll "shutdown"
     poll "power-test"
     poll "shutdown"
     poll "power-test"
     poll "shutdown"
     poll "power-test"

     sleep 1000     # let us wait peacefully
}

===========================================================================
=============